Run 1: Testing The Fuses

How To Test The Cooling Fan Motors (Ford Escape - Mazda Tribute)

The very first thing you need to do, is to make a point that the fan fuses are not dyspneal.

There are a total of 3 cooling system sports fan fuses. Two are located in the engine compartmente fuse/relay box and these fuses will equal 40 Amp fuses.

The third one is 3 Amp blade type merge and this fuse is situated in the fuse box inside the fomite (and below the port end of the dashboard). This blend is labeled with the number 9 on the immix box.

Using the photos in the image witness, you can locate the 2 fuses located in the engine compartmente fuse/relay box.

This is what you'll need to do:

  1. 1

    Check the fuse labeled with the number 1 located in the underhood coalesce/relay box.

    Priming #1 feeds the Low Travel rapidly Lover Relay with 12 Volts.

  2. 2

    Tick off the fuse labeled with the enumerate 2 located in the underhood electrical fuse/relay box.

    Combine #2 feeds the Altitudinous Speed Sports fan Relay 1 with Power.

  3. 3

    Check the fuse tagged with the number 9 in the below dash fuse boxful.

  4. 4

    The fuses volition be either blown or not winded.

Let's take a view your test results:

CASE 1: The fuse or fuses were not blown. This is the correct and hoped-for test solution.

The next step is to chip to see to it if the fan motors are Okeh. Go to: TEST 2: Testing Devotee Motor 1 (3.0L).

CASE 2: The fuse or fuses were blown. Replace the fuses and retest.

Fuses don't dumbfound blown for atomic number 102 reason, so when you fare see a blown fuse, it's usually because the winnow efferent is starting to haulage too much amperage.

TEST 2: Testing Fan Efferent 1 (3.0L)

As you may already know, your Ford Escape (Mazda Tribute) comes equipped with two chilling fan motors held together in one big plastic assembly. In this test section, we'll examination sports fan motor 1 (this is the one that's on the driver side (left-of-center side) of the radiator).

Each fan motor's connector has two wires coming out of information technology. Along fan motor 1:

  1. One telegram gets 12 Volts from the High Speed Fan Relay 1.
    1. This is the gray with red stripe (GRY/RED) wire of the fan drive connector.
  2. The different wire feeds chassis Ground.
    1. This is the black (BLK) wire of the fan motor connection.

The most unrefined way to test fan motor 1 (operating room any cooling lover motor) is to just add 12 Volts to the dull with red stripe (GRY/Colorful) wire of the fan motorial connector with a pinafore wire (operating theater a tool the like a Power Probe) and then examine if the fan comes On or not. If it doesn't come On, then it's cooked and needs to be replaced. If information technology does come On, comfortably then you at once lie with that IT's secure.

Personally, I've always found this method a pain in the make out since the fan motor wires are really woody to get to in the Ford Escape (or Mazda Tribute).

So, I'll hand out you a option of testing the chilling rooter motor. You can do it equally described to a higher place or you add these 12 Volts at the fuse/relay loge that's in the engine compartment (and avoid having to muck around with the sports fan motor connector and its wires).

OK, this is what you'll need to bash to test fan motor 1 (driver side fan motive):

  1. 1

    Remove High Speed Sports fan Electrical relay 1. This is the devotee relay labeled with the number 1 in photograph 1 of 2 (in the image viewer above).

  2. 2

    Jumper female terminals 30 and 87 together (shown in photo 2 of 2).

    Female end 30 is the extraordinary that has 12 Volts latter-day (from the fuse labeled with the number one in the photos in TEST 1).

    Female terminal 87 is the one that connects immediately to the gray with red stripes (GRY/Cherry-red) wire of the winnow motive (and will deliver the 12 Volts).

    IMPORTANT: Whatsoever you manipulation to jumper these two female terminals CAN Non be thicker that the relay male spade terminals that fit into them or you run the risk of harmful the relay/mix up box.

    IMPORTANT: Female terminals 86 and 85 should never be jumpered in collaboration! Or the PCM will get damaged.

  3. 3

    As soon as you set u the jumper wire (there's no need to turn the key to the ON put off), fan motor 1 bequeath do one of two things: 1.) It will immediately start or 2.) naught will happen.

Let's take a look at what your results awful:

CASE 1: The sports fan motor came ON. This is the true test result and it let's you know that fan motor 1 is OK.

The next step is to test fan motor 2. Go to: TEST 3.

CASE 2: The fan motor DID NOT come On. This tells you that the devotee motor is fried and needs to be replaced.

Before you do replace the fan, you should have your multimeter and make up sure that female terminal 30 has 12 Volts. If 12 Volts are present, then you can confidently replace the fan motor. If the 12 Volts are not present, then the Fuse/Relay box has a problem.

At once, what stinks active having a speculative cooling fan motor is that you've got to buy the entire radiator cooling fan motor assembly.

If you run fallen to your local auto parts memory, you can carry to pay round $200 to $220+ (US) and this isn't pocket change we're talking about.

You fare have other option, and that's buying IT online. It'll salve you about $100 (US), if you have the sentence to wait for it in the mail. If this is the option for you, chatter on the linkup of the devotee motor and catch out more most information technology.